METAL - International Conference on Metallurgy and Materials

Conference Proceedings - METAL 2020

29th International Conference on Metallurgy and Materials
May 20 - 22, 2020 / Brno, Czech Republic, EU
ISSN: 2694-9296
ISBN: 978-80-87294-97-0
Proceedings of the conference have been sent to Web of Science and Scopus for evaluation and potential indexing.

On the 29th International Conference on Metallurgy and Materials - METAL 2020, 215 people from 19 countries around the world were registered (such as the Czech Republic, Poland, Russian Federation, Slovakia, Lithuania, but also from Chile and Mexico). 226 articles were submitted to the following sections:
Session A - Advanced Iron, Cast Iron and Steelmaking
Session B - Metal Forming
Session C - Steel Products - properties
Session D - Modern Trends in Surface Engineering
Session E - Non-Ferrous Metals and Alloys
Session F - Economics and Management of Metallurgical Production

Read more
DZIEDZIC Michał AGH University of Science and Technology, Cracow, Poland, EU,
Co-authors: TURCZYN Stanisław
Abstract: The practical aim of the following study was to develop a new roll pass design (RPD) of the channels (UPN) and introduce it into industrial rolling. The necessity of usage of a charge stock with a greater cross section has caused necessity of an application of the new rolling schedule characterized by large deformations. [..] Read more
MORAVEC Ján University of Žilina, Žilina, Slovak Republic, EU,
Abstract: The paper deal with the unconventional method of creating cavities in samples. There is also described the principle of system for creating experimental samples. [..] Read more
BEHRENS Bernd-Arno Institut für Umformtechnik und Umformmaschinen (Forming Technology and Machines), Leibniz Universität Hannover, Garbsen, Germany, EU,,,,
Co-authors: URSINUS Jonathan BÜDENBENDER Christoph BRUNOTTE Kai NÜRNBERGER Florian DEMLER Eugen MAIER Hans Jürgen
Abstract: In order to reduce the number of process steps of steel forging processes. and thus also tool wear and process costs, tailored preform geometries can be produced by casting. [..] Read more
NAIZABEKOV Abdrakhman Rudny Industrial institute, Rudny, Kazakhstan;
Co-authors: LEZHNEV Sergey PANIN Yevgeniy ARBUZ Alexandr VOLOKITINA Irina VOLOKITIN Andrey
Abstract: Creation of new structural materials with new unique properties of metal remains one of the urgent tasks of modern materials science. In practice, it is possible to improve the properties of existing structural materials by grinding their structure to an ultra-fine-grained state. [..] Read more
BARTKOWSKA Aneta Poznan University of Technology, Faculty of Materials Engineering and Technical Physics, Poznan, Poland, EU,
Co-authors: JURČI Peter HUDÁKOVÁ Mária BARTKOWSKI Dariusz PRZESTACKI Damian KUSÝ Martin KUŘÍK Martin
Abstract: The paper presents the study results of microstructure, phase composition, microhardness and wear resistance of Vanadis-6 tool steel after diffusion boriding and laser processing. In this study the diode laser device was used. [..] Read more
SZKANDERA Pavel VSB - Technical University of Ostrava, Ostrava, Czech Republic, EU,,,,,,,
Co-authors: SADÍLEK Marek RUSZ Stanislav DOSTÁL Pavel DUBSKÝ Jaroslav ZELINKA Jan KOTÁSEK Ondřej
Abstract: The article is focused on the process of severe plastic deformation (SPD). New method using the SPD principle (DRECE) is described in the article. [..] Read more
OPĚLA Petr VSB – Technical University of Ostrava, Ostrava, Czech Republic, EU,
Co-authors: SCHINDLER Ivo RUSZ Stanislav ŠEVČÁK Vojtěch MAMUZIC Ilija
Abstract: A hot flow curve approximation performed via flow stress models as well as artificial neural networks requires precisely estimated constants. This estimation is in the case of highly-nonlinear issues often solved via gradient optimization algorithms. [..] Read more
KRÁTKÁ Ludmila VSB - Technical University of Ostrava, Ostrava, Czech Republic, EU,
Abstract: This study deals with the experimental processing of a tungsten heavy alloy prepared by powder metallurgy using the technology of rotary swaging. Rotary swaging took place at a temperature of 900 ° C. [..] Read more
BEHRENS Bernd-Arno Leibniz Universität Hannover, Institute of Forming Technology and Machines, An der Universität 2, 30823 Garbsen, Germany, EU,
Co-authors: BRUNOTTE Kai WESTER Hendrik Zaitsev Alexander HOOTAK Maiwand
Abstract: The approach of the most common industry-specific FE-systems for the service life evaluation of forming tools holds some disadvantages. For example, within the decoupled tool analysis, load situations are typically analysed at room temperature and thus, the transient temperature development in the forging die is not considered in the lifetime evaluation. [..] Read more
GAMIN Yury National University of Science and Technology «MISIS», Moscow, Russian Federation,
Co-authors: KOSHMIN Alexander DOLBACHEV Alexander
Abstract: The main goal of this study is to analyze the influence of radial-shear rolling (RSR) modes on the structure and properties of 1050A using finite element modeling (FEM) and experimental verification of the results. Ingots with a diameter of 60 mm were obtained, which were rolled into rods with a diameter of 14 mm at different regimes (total elongation ratio µ = 18.4). [..] Read more
ARBUZ Alexandr Nazarbayev University, Nur-Sultan, Kazakhstan,,
Co-authors: KAWALEK Anna OZHMEGOV Kirill DANIYEVA Nurgul PANIN Evgeniy
Abstract: An overview of the prospects for the development of nuclear technologies and the conclusion of the relevant requirements for advanced structural materials, their classification and features were described. In order to obtain a bar with a modified radiation-resistant outer layer, an experiment on radial-shear rolling of the Zr-1% Nb alloy in conditions favorable for the UFG structure formation was conducted. [..] Read more
HILŠER Ondřej VSB - Technical University of Ostrava, Faculty of Mechanical Engineering, Department of Mechanical Technology, Ostrava, Czech Republic, EU,,,,
Co-authors: RUSZ Stanislav PASTRŇÁK Martin ZABYSTRZAN Rostislav
Abstract: Development of technologies to produce the very fine structure is currently very intensively accelerated. Even in scientific research, it is recognized that precisely controlled forming processes, including special processes, enabling control of technological parameters with regard to the structure refinement, and tied with the strengthening of materials, currently had the highest gradient of utilization efficiency of the scientific research findings in practice. [..] Read more
HILŠER Ondřej VSB - Technical University of Ostrava, Ostrava, Czech Republic, EU,,,
Co-authors: SNOPIŃSKI Przemysław RUSZ Stanislav TAŃSKI Tomasz MAZIARZ Wojciech STAN-GŁOWIŃSKA Katarzyna GREGER Miroslav
Abstract: In this article a continuous severe plastic deformation (SPD) process entitled dual rolls equal channel extrusion (DRECE) for producing ultrafine-grained (UFG) microstructure of thin sheets is presented. The DRECE process combines conventional equal channel angular pressing (ECAP) process and continual CONFORM process, and it can be easily scaled for industrial use. [..] Read more
BEHRENS Bernd-Arno Institute of Forming Technology and Machines, Leibniz Universität Hannover, 30823 Garbsen, Deutschland,
Co-authors: UHE Johanna WESTER Hendrik STOCKBURGER Eugen
Abstract: A possible alternative to the established press hardening steel 22MnB5 are hot formed martensitic chromium steels. Both strength and ductility of the martensitic chromium steels can reach very high values with appropriate heat treatments. [..] Read more
STEJSKALOVÁ Šárka Material and Metallurgical Research, Ltd., Ostrava, Czech Republic, EU,
Co-authors: KUBOŇ Zdeněk ROŽNOVSKÁ Gabriela
Abstract: Low-alloy steel 16Mo3 is often used for tubes and other components of the pressure system of a boiler operating at elevated temperature (up to 530 °C). Long-term exposure of low-alloy steel components at elevated temperatures inevitably result in some kind of structural degradation; for example, creep cavitation, carbide coarsening and/or spheroidization, and, less commonly, also graphitization. [..] Read more
KOLAŘÍKOVÁ Marie CTU - Czech Technical University of Prague, Faculty of Mechanical Engineering, Technická 4, Prague, Czech Republic, EU,
Co-authors: KOLAŘÍK Ladislav KRÁLÍK Vlastimil SOVA Jan
Abstract: During resistance welding, the electrode tips are significantly worn. The amount of wear is strongly dependent on the welded material, the surface treatment of the welded sheet, the thickness of the surface treatment, the welding parameters and, last but not least, especially on the number of performed welds. [..] Read more
SOROKINA Svetlana Faculty of materials science and technology, VŠB-Technical University of Ostrava, 17. listopadu 15, Ostrava-Poruba, 708 00, Czech Republic, EU,
Co-authors: SMETANA Bedřich DROZDOVÁ Ľubomíra KAWULOKOVÁ Monika ZLÁ  Simona
Abstract: Knowledge of thermodynamical and thermophysical properties of materials plays an important role for many industrial applications. The paper is dedicated to the study of three model alloys based on Fe-C-Cr-Ni. [..] Read more
BRUSILOVÁ Alena Slovak University of Technology in Bratislava, Bratislava, Slovak Republic, EU,
Co-authors: SCHREK Alexander POKUSOVÁ Marcela
Abstract: The combination of different mechanical properties of tailor welded blanks (TWB-s) results in non-constant plastic flow and instability of the weld interface during forming. This is most marked when combining metal sheets of different thicknesses or sheets with significantly different plastic characteristics. [..] Read more
Matuszewski Mateusz Czestochowa University of Technology, Czestochowa, Poland, EU,
Co-authors: Koňár Radoslav Harmaniak Daniel Zaborski Andrzej
Abstract: In the paper, the methods for determining heat affected zones during arc weld surfacing is presented. For this purpose, numerical simulations of the temperature field were performed using the Ansys and Sysweld programs based on the finite element method. [..] Read more
Averina Julia Russian University of Chemical Technology Mendeleev, Moscow, Russia,
Co-authors: Zhukov Dmitry Tsevkova Victoria Safarova Irina Subcheva Elena
Abstract: Alloys used for the manufacture of various structures must be strong and easy to process. Under certain conditions, hydrogen can adversely affect the fracture characteristics of most structural alloys. [..] Read more
Scroll to Top